[nextpage title=”Introduction”]
Today we are reviewing another CPU cooler from Arctic Cooling, the Freezer 13 Pro. It has a tower heatsink, four 8 mm heatpipes and a 120 mm fan. Check it out!
As well as most Arctic Cooling products, the Freezer 13 Pro comes on a plastic blister instead of a cardpaper box.
Figure 2 shows what is inside the package: the cooler itself, manual, and installation hardware.
In Figure 3, you can see the Arctic Cooling Freezer 13 Pro.
This cooler is discussed in detail in the following pages.
[nextpage title=”The Freezer 13 Pro”]
In Figure 4, you have a front view of the cooler, where the nine-blade fan is visible.
Figure 5 shows the side of the cooler. Note that the fins are folded, creating a closed surface.
Figure 6 reveals the rear side of the cooler.
In Figure 7 you see the top of the cooler. Note the "V" cut on the fins, which grants access to the screw that holds the cooler in place.
[nextpage title=”The Freezer 13 Pro (Cont’d)”]
Figure 8 shows the base of the cooler, which comes with preapplied thermal grease. Note the thick U-shaped heatpipes.
In Figure 9, the heatsink of the Freezer 13 Prois shown without the fan.
Figure 10 shows the 120- mm fan detached from the heatsink.
Figure 11 displays a unique feature of the Freezer 13 Pro: a small centrifugal fan over the cooler base that, according to the manufacturer, helps cool the components surrounding the CPU, such as the motherboard chipset and the transistors on the voltage regulator circuit.
[nextpage title=”Installation”]
Figure 12 shows, at the left, the metal clips needed to install the Freezer 13 Pro on AMD CPUs. At the center and right, are the pins and frame required to install it on Intel processors
In Figure 13 you see the Intel frame installed on our motherboard. After that, all you need to do is to put the cooler over the CPU and fasten two screws.
Figure 13: Frame for Intel CPUs installed
Figure 14 presents the Freezer 13 Pro installed in our case.
Figure 14: Installed in our system
[nextpage title=”How We Tested”]
We tested the cooler with a Core i7-860 CPU (quad-core, 2.8 GHz), which is a socket LGA1156 processor with a 95 W TDP (Thermal Design Power). In order to get higher thermal dissipation, we overclocked it to 3.3 GHz (150 MHz base clock and 22x multiplier), keeping the standard core voltage (Vcore), which was the maximum stable overclock we could make with the stock cooler. Keep in mind that we could have raised the CPU clock more, but to include the stock cooler in our comparison, we needed to use this moderate overclock.
We measured noise and temperature with the CPU idle and under full load. In order to get 100% CPU usage in all threads, we ran Prime 95 25.11 with the "In-place Large FFTs" option. (In this version, the software uses all available threads.)
We compared the tested cooler to the Intel stock cooler with a copper base (included with the CPU), as well as with other coolers. Note that in the past, we tested coolers with a socket LGA775 CPU, and we retested some "old" coolers with this new methodology. This means you can find different values in older reviews than the values you will read in the next page. Every cooler was tested with the thermal compound that accompanies it.
Room temperature measurements were taken with a digital thermometer. The core temperature was
read with the SpeedFan program (available from the CPU thermal sensors), using an arithmetic average of the core temperature readings. During the tests, the left panel of the case was open.
The sound pressure level (SPL) was measured with a digital noise meter, with its sensor placed 4" (10 cm) from the fan. We turned off the case and video board cooler fans so they wouldn’t interfere with the results. This measurement is only for comparison purposes, because a precise SPL measurement needs to be made inside an acoustically insulated room with no other noise sources, which isn’t the case here.
Hardware Configuration
- Processor: Core i7-860
- Motherboard: Gigabyte P55A-UD6
- Memory: 2 GB Markvision (DDR3-1333/PC3-10700 with 9-9-9-22 timings), configured at 1,200 MHz
- Hard disk: Seagate Barracuda XT 2 TB
- Video card: Zotac GeForce GTS 250
- Video resolution: 1680×1050
- Video monitor: Samsung Syncmaster 2232BW Plus
- Power supply: Seventeam ST-550P-AM
- Case: 3RSystem L-1100 T.REX Cool
Operating System Configuration
- Windows 7 Home Premium 64 bit
Software Used
Error Margin
We adopted a 2 °C error margin, meaning temperature differences below 2 °C are considered irrelevant.
[nextpage title=”Our Tests”]
The table below presents the results of our measurements. We repeated the same test on all coolers listed below. Each measurement was taken with the CPU at idle and at full load. In the models with a fan supporting PWM, the motherboard controlled the fan speed according to core load and temperature. On coolers with an integrated fan controller, the fan was set at the minimum speed on the idle test and at full speed on the full load test.
Idle Processor |
Processor at Full Load |
||||||
Cooler | Room Temp. | Noise | Speed | Core Temp. | Noise | Speed | Core Temp. |
Intel stock (socket LGA1156) | 14 °C | 44 dBA | 1700 rpm | 46 °C | 54 dBA | 2500 rpm | 90 °C |
Cooler Master Hyper TX3 G1 | 14 °C | 47 dBA | 2050 rpm | 33 °C | 56 dBA | 2900 rpm | 62 °C |
Zalman CNPS10X Extreme | 14 °C | 45 dBA | 1400 rpm | 27 °C | 53 dBA | 1950 rpm | 51 °C |
Thermaltake Silent 1156 | 14 °C | 44 dBA | 1200 rpm | 38 °C | 49 dBA | 1750 rpm | 69 °C |
Noctua NH-D14 | 14 °C | 49 dBA | 1250 rpm | 27 °C | 49 dBA | 1250 rpm | 53 °C |
Zalman CNPS10X Performa | 14 °C | 46 dBA | 1500 rpm | 28 °C | 52 dBA | 1950 rpm | 54 °C |
Prolimatech Megahalems | 14 °C | 40 dBA | 750 rpm | 27 °C | 60 dBA | 2550 rpm | 50 °C |
Thermaltake Frio | 14 °C | 46 dBA | 1450 rpm | 27 °C | 60 dBA | 2500 rpm | 50 °C |
Prolimatech Samuel 17 | 14 °C | 40 dBA | 750 rpm | 40 °C | 60 dBA | 2550 rpm | 63 °C |
Zalman CNPS8000A | 18 °C | 43 dBA | 1400 rpm | 39 °C | 54 dBA | 2500 rpm | 70 °C |
Spire TherMax Eclipse II | 14 °C | 55 dBA | 2200 rpm | 28 °C | 55 dBA | 2200 rpm | 53 °C |
Scythe Ninja3 | 17 °C | 39 dBA | 700 rpm | 32 °C | 55 dBA | 1800 rpm | 57 °C |
Co rsair A50 |
18 °C | 52 dBA | 1900 rpm | 33 °C | 52 dBA | 1900 rpm | 60 °C |
Thermaltake Jing | 18 °C | 44 dBA | 850 rpm | 34 °C | 49 dBA | 1300 rpm | 60 °C |
GlacialTech Alaska | 18 °C | 43 dBA | 1150 rpm | 36 °C | 51 dBA | 1600 rpm | 60 °C |
Deepcool Gamer Storm | 18 °C | 43 dBA | 1100 rpm | 35 °C | 48 dBA | 1600 rpm | 62 °C |
Corsair A70 | 26 °C | 56 dBA | 1900 rpm | 40 °C | 56 dBA | 1900 rpm | 65 °C |
Deepcool Ice Blade Pro | 23 °C | 45 dBA | 1200 rpm | 38 °C | 52 dBA | 1500 rpm | 64 °C |
AC Freezer 7 Pro Rev. 2 | 23 °C | 47 dBA | 1750 rpm | 44 °C | 51 dBA | 2100 rpm | 77 °C |
Corsair H70 | 27 °C | 60 dBA | 1900 rpm | 37 °C | 60 dBA | 1900 rpm | 61 °C |
Zalman CNPS9900 Max | 27 °C | 55 dBA | 1600 rpm | 38 °C | 58 dBA | 1750 rpm | 63 °C |
Arctic Cooling Freezer 11 LP | 25 °C | 45 dBA | 1700 rpm | 51 °C | 49 dBA | 1950 rpm | 91 °C |
CoolIT Vantage | 26 °C | 60 dBA | 2500 rpm | 37 °C | 60 dBA | 2500 rpm | 62 °C |
Deepcool Ice Matrix 600 | 25 °C | 46 dBA | 1100 rpm | 41 °C | 53 dBA | 1300 rpm | 69 °C |
Titan Hati | 26 °C | 46 dBA | 1500 rpm | 40 °C | 57 dBA | 2450 rpm | 68 °C |
Arctic Cooling Freezer 13 | 27 °C | 49 dBA | 1950 rpm | 41 °C | 53 dBA | 2300 rpm | 70 °C |
Noctua NH-C14 | 26 °C | 52 dBA | 1300 rpm | 37 °C | 52 dBA | 1300 rpm | 61 °C |
Intel XTS100H | 26 °C | 49 dBA | 1200 rpm | 42 °C | 64 dBA | 2600 rpm | 68 °C |
Zalman CNPS5X SZ | 23 °C | 52 dBA | 2250 rpm | 38 °C | 57 dBA | 2950 rpm | 69 °C |
Thermaltake SlimX3 | 21 °C | 50 dBA | 2700 rpm | 46 °C | 50 dBA | 2750 rpm | 99 °C |
Cooler Master Hyper 101 | 21 °C | 50 dBA | 2600 rpm | 38 °C | 57 dBA | 3300 rpm | 71 °C |
Antec Kühler H2O 620 | 19 °C | 52 dBA | 1400 rpm | 34 °C | 55 dBA | 1400 rpm | 58 °C |
Arctic Cooling Freezer 13 Pro | 20 °C | < font size="1">46 dBA | 1100 rpm | 36 °C | 49 dBA | 1300 rpm | 62 °C |
In the graph below, at full load you can see how many degrees Celsius hotter the CPU core is than the air outside the case. The lower this difference, the better is the performance of the cooler.
[nextpage title=”Main Specifications”]
The main features of the Arctic Cooling Freezer 13 Pro cooler include:
- Application: Sockets 775, 1155, 1156, 1366, AM3, AM2+, and AM2 processors
- Fins: Aluminum
- Base: Copper
- Heat-pipes: Four 8 mm copper heatpippes
- Fan: one 120 mm main fan, one 50 mm auxiliary fan
- Nominal fan speed: 1,350 rpm
- Fan air flow: 49.7 cfm
- Maximum power consumption: Not informed
- Nominal noise level: Not informed
- Weight: 2.3 lbs (1.05 kg)
- More information: https://www.arctic.ac
- Average price in the US*: USD 39.00
* Researched at Amazon.com on the day we published this review.[nextpage title=”Conclusions”]
The Freezer 13 Pro draws attention. It has good looks, and also a unique feature that may intrigue most users: the small centrifugal fan over its base. The highlights of the Freezer 13 Pro are the easy installation and the low noise level; it is actually one of the quietest coolers we tested to date. It is also not too expensive.
However, when describing performance, the Freezer 13 Pro is a good cooler, but not a high-end one. It received a technical draw with its "little brother," the Freezer 13.
Being a quiet, easy-to-install, good cooler with a good cost/performance ratio, the Arctic Cooling Freezer 13 Pro receives the Hardware Secrets Silver Award.
Leave a Reply