Corsair TX750 V2 Power Supply Review
Load Tests
Contents
We conducted several tests with this power supply, as described in the article Hardware Secrets Power Supply Test Methodology.
First we tested this power supply with five different load patterns, t
rying to pull around 20%, 40%, 60%, 80%, and 100% of its labeled maximum capacity (actual percentage used listed under “% Max Load”), watching the behavior of the reviewed unit under each load. In the table below, we list the load patterns we used and the results for each load.
If you add all the powers listed for each test, you may find a different value than what is posted under “Total” below. Since each output can have a slight variation (e.g., the +5 V output working at +5.10 V), the actual total amount of power being delivered is slightly different than the calculated value. In the “Total” row, we are using the real amount of power being delivered, as measured by our load tester.
The +12VA and +12VB inputs listed below are the two +12 V independent inputs from our load tester. During our tests, the +12VA and +12VB input were connected to the power supply single +12 V rail (the EPS12V connector was installed on the +12VB input of our load tester).
|
Input |
Test 1 |
Test 2 |
Test 3 |
Test 4 |
Test 5 |
|
+12VA |
5 A (60 W) |
11 A (132 W) |
16 A (192 W) |
22 A (264 W) |
27 A (324 W) |
|
+12VB |
5 A (60 W) |
10 A (120 W) |
16 A (192 W) |
21 A (252 W) |
27 A (324 W) |
|
+5V |
2 A (10 W) |
4 A (20 W) |
6 A (30 W) |
8 A (40 W) |
10 A (50 W) |
|
+3.3 V |
2 A (6.6 W) |
4 A (13.2 W) |
6 A (19.8 W) |
8 A (26.4 W) |
10 A (33 W) |
|
+5VSB |
1 A (5 W) |
1.5 A (7.5 W) |
2 A (10 W) |
2.5 A (12.5 W) |
3 A (15 W) |
|
-12 V |
0.5 A (6 W) |
0.5 A (6 W) |
0.5 A (6 W) |
0.5 A (6 W) |
0.5 A (6 W) |
|
Total |
147.6 W |
298.2 W |
412.4 W |
598.4 W |
748.4 W |
|
% Max Load |
19.7% |
39.8% |
55.0% |
79.8% |
99.8% |
|
Room Temp. |
46.3° C |
45.6° C |
46.0° C |
49.8° C |
45.1° C |
|
PSU Temp. |
38.9° C |
40.8° C |
41.8° C |
44.2° C |
45.6° C |
|
Voltage Regulation |
Pass |
Pass |
Pass |
Pass |
Pass |
|
Ripple and Noise |
Pass |
Pass |
Pass |
Pass |
Pass |
|
AC Power |
177.4 W |
348.2 W |
483.4 W |
710.0 W |
905.0 W |
|
Efficiency |
83.2% |
85.6% |
85.3% |
84.3% |
82.7% |
|
AC Voltage |
117.6 V |
116.5 V |
114.9 V |
112.5 V |
109.4 V |
|
Power Factor |
0.985 |
0.989 |
0.993 |
0.996 |
0.998 |
|
Final Result |
Pass |
Pass |
Pass |
Pass |
Pass |
The Corsair TX750 V2 passed our test with flying colors, being able to deliver its labeled wattage at high temperatures.
Efficiency was very good, between 82.7% and 85.6%, correctly matching the 80 Plus Bronze certification, which requires a minimum 82% efficiency at light (20%) and full loads, and 85% minimum at typical (50%) load.
Voltage regulation was superb, with all voltages within 3% of their nominal values, including the -12 V output. The ATX12V specification allows voltages to be up to 5% from their nominal values (10% for the -12 V output). Therefore this power supply presents voltages closer to their nominal values than necessary all the time.
Noise and ripple levels were always extremely low. Below you can see the results for the power supply outputs during test number five. The maximum allowed is 120 mV for the +12 V and -12 V outputs, and 50 mV for the +5 V, +3.3 V, and +5VSB outputs. All values are peak-to-peak figures.
Figure 19: +12VA input from load tester during test five at 748.4 W (24.2 mV)
Figure 20: +12VB input from load tester during test five at 748.4 W (28.2 mV)
Figure 21: +5V rail during test five at 748.4 W (9.2 mV)
Figure 22: +3.3 V rail during test five at 748.4 W (8 mV)
Let’s see if we can pull even more from the Corsair TX750 V2.