[nextpage title=”Introduction”]

The Dragon Rider is the latest full-tower case from In Win. Its left-side panel is identical to the one used on the Ironclad and on the Maelstrom –two full-tower cases from In Win –, but the Dragon Rider brings several new features. Let’s take a look at them!

Differently from most cases, the Dragon Rider comes with a 120 mm fan on its right panel to cool down the bottom area of the CPU. This fan is attached to a standard peripheral power connector, and thus you can’t monitor its speed.

In Win Dragon Rider caseFigure 1: In Win Dragon Rider case

In Win Dragon Rider caseFigure 2: In Win Dragon Rider case

The left panel, better seen in Figure 3, comes with a big 220 mm fan that glows in blue when turned on. A switch is available for you to turn off the LEDs, and the fan is connected to a standard peripheral power connector, so you can’t monitor its speed. If you remove this fan you can install up to six 120 mm fans. So, if you are paranoid with air flow, this case should please you. On the good side, all holes for screwing the fans have a rubber washer, helping reducing vibration and thus noise. On the bad side, both the left and the righr panels don’t come with air filters.

In Win Dragon Rider caseFigure 3: Left panel

[nextpage title=”The Front Panel, Buttons and Connectors”]

The front panel of the Dragon Rider can be seen in Figure 4. This case has five 5.25” bays, and the top-most can be used as an external 3.5” bay. All bays feature meshed covers with air filters. At the bottom part of the front panel there is a 120 mm fan, this time with a three-pin connector, so you can install it on the motherboard and, thus, monitor its speed.

In Win Dragon Rider caseFigure 4: Front panel

In Win Dragon Rider caseFigure 5: Front fan

The buttons and connectors of this case come on the top panel, and it is one of the most complete panels we’ve seen to date. This case comes with two USB 3.0 ports, two USB 2.0 ports, two eSATA ports, one FireWire (IEEE1394) port, and the traditional audio jacks.

In Win Dragon Rider caseFigure 6: Buttons and connectors

[nextpage title=”Top, Bottom and Rear Panels”]

The top panel of the Dragon Rider can be seen in Figure 7. It comes with one 120 mm fan identical to the front one, and you can install a second 120 mm fan, if you’d like to. The top fan can be removed if you want to install a 240 mm internal radiator from a liquid cooling solution.

In Win Dragon Rider caseFigure 7: Top panel

The bottom panel (Figure 8), features an air intake for the power supply fan and you can choose to have the case feet showing or not.

In Win Dragon Rider caseFigure 8: Bottom panel

In Figure 9, you can see the rear panel of the Dragon Rider. It comes with a 120 mm fan that is identical to the ones from the top and front panels. The power supply is installed at the bottom of the case, and the rear panel and the interior of the case are painted black. The Dragon Rider has eight expansion slots, which is definitely a plus, allowing you to install a dual-slot video card in the last slot of the motherboard (most cases come with seven slots, therefore not allowing this installation). All of them come with meshed covers.

The case also has four holes with rubber covers, two of them are for you to pass hoses of liquid cooling solutions, and the other two you must use to pass the cables coming from the USB 3.0 ports, which must be installed on the rear USB 3.0 ports of your motherboard.

In Win Dragon Rider caseFigure 9: Rear panel

Let’s now take a look inside the Dragon Rider.

[nextpage title=”Inside the Dragon Rider”]

Both panels are attached to the chassis using black thumbscrews. Before talking about the interior of the Dragon Rider, let’s show the other side of the side panels (see Figures 10 and 11). As you can see, the left panel is covered with foam in order to reduce the noise level produced by the computer.

In Win Dragon Rider caseFigure 10: Left panel

In Win Dragon Rider caseFigure 11: Right panel

The motherboard tray has a huge hole around the area where the CPU is installed, so you can replace the backplate of the CPU cooler without the need to remove your motherboard. Also, there is a 120 mm fan cooling down the bottom part of the CPU.

You can route cables behind the motherboard tray, thanks to the presence of two holes on the motherboard tray. Plus, the motherboard tray doesn’t go all the way down to the bottom panel, making it very easy to route the power supply and hard drive cables.

In Win Dragon Rider caseFigure 12: Overall look

In Win Dragon Rider caseFigure 13: A view behind the motherboard tray

[nextpage title=”Inside the Dragon Rider (Cont’d)”]

The Dragon Rider supports Extended ATX motherboards and video cards up to 12.6” (320 mm) long. Expansion cards are fastened using individual tool-less mechanisms that are very sturdy.

In Win Dragon Rider caseFigure 14: Overall look

In Win Dragon Rider caseFigure 15: Tool-less installation mechanisms

In the Dragon Rider you can install the power supply with its bottom fan facing up or facing down, so you will have to decide if you want the power supply to be pulling cool air from outside the case (fan facing down) or hot air from inside the case (fan facing up). The product comes with an air filter for the power supply fan, which is great. There are also four rubber stands for the power supply.

In Win Dragon Rider caseFigure 16: Power supply compartment

[nextpage title=”The Disk Drive Bays”]

The Dragon Rider comes with five 5.25” external bays, six internal 3.5” bays, and one internal 2.5” bay. One external 3.5” device can be installed using the 5.25”-to-3.5” adapter that comes installed on the top-most 5.25” bay. This adapter can also be used by a hard drive, so you have up to seven 3.5” hard drives installed, plus a 2.5” hard drive or SSD. Sweet!

In Win Dragon Rider caseFigure 17: Drive bays

In Win Dragon Rider caseFigure 18: 5.25”-to-3.5” adapter

All drive bays use tool-less installation mechanisms, except the 2.5” one. The system used on the Dragon Rider requires a rail to be installed on each side of the drive to be installed, and then sliding the drive inside the proper bay. To remove 5.25” devices, however, you have to first remove the front panel in order to have access to the rails release tabs. These rails come inside a storage compartment that comes installed in the bottom-most 5.25” bay.

In Win Dragon Rider caseFigure 19: Rails

The 2.5” bay is available inside a drawer.

In Win Dragon Rider caseFigure 20: 2.5” drawer

In Figure 21, you can see the accessories that come with the product.

In Win Dragon Rider caseFigure 21: Accessories

[nextpage title=”Main Specifications”]

The main specs for the In Win Dragon Rider case include:

  • Style: Full-tower
  • Application: E-ATX and smaller form factors derived from this one
  • Power supply: Doesn’t come with the product
  • Available colors: Black
  • Material: Steel
  • Side panel: Meshed
  • Dimensions: 21.9 x 9.4 x 22.8 inches (556 x 239 x 578 mm) (H x W x D)
  • Net weight: 27 lbs (12 kg)
  • Gross weight: 32 lbs (14.4 kg)
  • Bays: Five external 5.25” bays, one external/internal 3.5” bay converted from one 5.25” bay, six internal 3.5” bays, and one internal 2.5” bay
  • Expansion slots: Eight
  • Maximum video card length: 12.6” (320 mm)
  • Maximum CPU cooler height: NA
  • Fans: One 120 mm fan on the front panel, one 120 mm fan on the top panel, one 120 mm fan on the top panel, one 120 mm on the right panel, and one 220 mm fan on the left panel
  • Optional fans: One 120 mm fan on the top panel, six 120 mm fans on the left panel (if the 220 mm is removed)
  • More Information: https://www.inwin-style.com
  • Average price in the US*: USD 140.00 (USD 120 after mail-in rebate)

* Researched at Newegg.com on the day we published this review.

[nextpage title=”Conclusions”]

The Dragon Rider is a very nice full-tower case if you are looking for a case with lots of nice features supporting several fans.

Strong Points

  • Meshed covers on the external bays with air filters
  • Air filter for the front fan
  • Air filter for the power supply fan
  • Fan for cooling down the bottom of the CPU
  • Massive number of fans (case comes with five and supports up to 11)
  • Six 3.5” hard drive bays (seven if the 5.25”-to-3.5” adapter is used)
  • 2.5” hard drive/SSD bay
  • Tool-less mechanisms for installing drives
  • Individual tool-less mechanisms for fastening expansion cards that are very sturdy
  • Eight expansion slots
  • Meshed slot covers
  • A huge hole in the motherboard tray for accessing the backplate of the CPU cooler
  • Holes for routing cables behind the motherboard tray
  • Rear panel and interior are painted black
  • Excellent number of expansion ports: two USB 2.0, two USB 3.0, two eSATA and one FireWire
  • No sharp edges where you could cut yourself while building your computer

Weak Points

  • No air filter on the left-side panel
  • No air filter on the right-side panel