We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.

[nextpage title=”Introduction”]

The NZXT Respire T20 is a CPU cooler with a tower heatsink, a 120 mm fan, and three heatpipes (one 8 mm and two 6 mm). Check it out!

The Respire T20 is a smaller (and cheaper) version of the Respire T40, which we reviewed recently. Its box is shown in Figure 1.

Figure 1: Package

Figure 2 shows the contents of the box: the cooler, a power adapter, a small bag of thermal compound, manual, and installation hardware.

Figure 2: Accessories

Figure 3 displays the Respire T20.

Figure 3: The Respire T20

This cooler is discussed in detail in the following pages.

[nextpage title=”The NZXT Respire T20″]

Figure 4 illustrates the front of the Respire T20, where the 120 mm fan goes.

Figure 4: Front view

Figure 5 reveals the side of the cooler. Notice that the center heatpipe, which is 8 mm in diameter, is larger than the side ones, which are 6 mm in diameter.

Figure 5: Side view

Figure 6 unveils the rear side of the cooler. You can see the “step” between the sides of the fins.

Figure 6: Rear view

In Figure 7, you can see the top of the cooler, where the tips of the heatpipes are visible.

Figure 7: Top view

[nextpage title=”The NZXT Respire T20 (Cont’d)”]

Figure 8 illustrates the base of the cooler. The heatpipes touch the CPU directly, and there is no gap between them. The surface is not polished enough for a mirror-like look.

Figure 8: Base

Figure 9 reveals the heatsink with the fan removed.

Figure 9: The heatsink

Figure 10 shows the 120 mm fan that comes with the cooler, mounted on its plastic holder. This fan has a three-pin connector, which means it is not compatible with PWM speed control.

Figure 10: Fan

[nextpage title=”Installation”]

Figure 11 shows the backplate and the four screws that must be installed on the solder side of the motherboard prior to installing the Respire T20; it also displays the plastic spacers that go on the component side.

Figure 11: Backplate

In Figure 12, you can see the two metal pieces wherein the cooler will be screwed.

Figure 12: Metal holders

Put the heatsink in place, and attach it to the metal pieces using a third bar and two nuts.

Figure 13: Heatsink installed

Finally, reinstall the fan.

Figure 14: Installation finished

[nextpage title=”How We Tested”]

We tested the cooler with a Core i5-2500K CPU (quad-core, 3.3 GHz), which is a socket LGA1155 processor with a 95 W TDP (Thermal Design Power). In order to get higher thermal dissipation, we overclocked it to 4.0 GHz (100 MHz base clock and x40 multiplier), with 1.3 V core voltage (Vcore). This CPU was able to reach 4.8 GHz with its default core voltage, but at this setting, the processor enters thermal throttling when using mainstream coolers, reducing the clock and thus the thermal dissipation. This could interfere with the temperature readings, so we chose to maintain a moderate overclocking.

We measured noise and temperature with the CPU under full load. In order to get 100% CPU usage in all cores, we ran Prime 95 25.11 with the “In-place Large FFTs” option. (In this version, the software uses all available threads.)

We compared the tested cooler to other coolers we already tested, and to the stock cooler that comes with the Core i5-2500K CPU. Note that the results cannot be compared to measures taken on a different hardware configuration, so we retested some “old” coolers with this new methodology. This means you can find different values in older reviews than the values you will read on the next page. Every cooler was tested with the thermal compound that comes with it.

Room temperature measurements were taken with a digital thermometer. The core temperature was read with the SpeedFan program (available from the CPU thermal sensors), using an arithmetic average of the core temperature readings.

Dur
ing the tests, the panels of the computer case were closed. The front and rear case fans were spinning at minimum speed in order to simulate the “normal” cooler use on a well-ventilated case. We assume that is the common setup used by a cooling enthusiast or overclocker.

The sound pressure level (SPL) was measured with a digital noise meter, with its sensor placed near the top opening of the case. This measurement is only for comparison purposes, because a precise SPL measurement needs to be made inside an acoustically insulated room with no other noise sources, which is not the case here.

Hardware Configuration

• Processor: Core i5-2500K
• Motherboard: ASUS Maximus IV Extreme-Z
• Memory: 16 GB G.Skill Sniper (DDR3-1600/PC3-12800), configured at 1,600 MHz
• Hard disk: Seagate Barracuda XT 2 TB
• Video card: Point of View GeForce GTX 460 1 GB
• Video resolution: 1920×1080
• Video monitor: Samsung SyncMaster P2470HN
• Power supply: Seventeam ST-550P-AM
• Case:  Cooler Master HAF 922

Operating System Configuration

• Windows 7 Home Premium 64 bit SP1

Software Used

• Prime95
• SpeedFan

Error Margin

We adopted a 2°C error margin, meaning temperature differences below 2°C are considered irrelevant.

[nextpage title=”Our Tests”]

The table below presents the results of our measurements. We repeated the same test on all coolers listed below. Each measurement was taken with the CPU at full load. In the models with a fan supporting PWM, the motherboard controlled the fan speed according to core load and temperature. On coolers with an integrated fan controller, the fan was set at the full speed.

Cooler	Room Temp.	Noise	Speed	Core Temp.	Temp. Diff.
Cooler Master Hyper TX3	18 °C	50 dBA	2850 rpm	69 °C	51 °C
Corsair A70	23 °C	51 dBA	2000 rpm	66 °C	43 °C
Corsair H100	26 °C	62 dBA	2000 rpm	64 °C	38 °C
EVGA Superclock	26 °C	57 dBA	2550 rpm	67 °C	41 °C
NZXT HAVIK 140	20 °C	46 dBA	1250 rpm	65 °C	45 °C
Thermalright True Spirit 120	26 °C	42 dBA	1500 rpm	82 °C	56 °C
Zalman CNPS12X	26 °C	43 dBA	1200 rpm	71 °C	45 °C
Zalman CNPS9900 Max	20 °C	51 dBA	1700 rpm	62 °C	42 °C
Titan Fenrir Siberia Edition	22 °C	50 dBA	2400 rpm	65 °C	43 °C
SilenX EFZ-120HA5	18 °C	44 dBA	1500 rpm	70 °C	52 °C
Noctua NH-L12	20 °C	44 dBA	1450 rpm	70 °C	50 °C
Zalman CNPS8900 Extreme	21 °C	53 dBA	2550 rpm	71 °C	50 °C
Gamer Storm Assassin	15 °C	48 dBA	1450 rpm	58 °C	43 °C
Deepcool Gammaxx 400	15 °C	44 dBA	1500 rpm	60 °C	45 °C
Cooler Master TPC 812	23 °C	51 dBA	2350 rpm	66 °C	43 °C
Deepcool Gammaxx 300	18 °C	43 dBA	1650 rpm	74 °C	56 °C
Intel stock cooler	18 °C	41 dBA	2000 rpm	97 °C	79 °C
Xigmatek Praeton	19 °C	52 dBA	2900 rpm	83 °C	64 °C
Noctua NH-U12P SE2	18 °C	42 dBA	1300 rpm	69 °C	51 °C
Deepcool Frostwin	24 °C	46 dBA	1650 rpm	78 °C	54 °C
Thermaltake Frio Advanced	13 °C	56 dBA	2000 rpm	62 °C	49 °C
Xigmatek Dark Knight Night Hawk Edition	9 °C	48 dBA	2100 rpm	53 °C	44 °C
Thermaltake Frio Extreme	21 °C	53 dBA	1750 rpm	59 °C	38 °C
Noctua NH-U9B SE2	12 °C	44 dBA	1700 rpm	64 °C	52 °C
Thermaltake WATER2.0 Pro	15 °C	54 dBA	2000 rpm	52 °C	37 °C
Deepcool Fiend Shark	18 °C	45 dBA	1500 rpm	74 °C	56 °C
Arctic Freezer i30	13 °C	42 dBA	1350 rpm	63 °C	50 °C
Spire TME III	8 °C	46 dBA	1700 rpm	70 °C	62 °C
Thermaltake WATER2.0 Performer	11 °C	54 dBA	2000 rpm	49 °C	38 °C
Arctic Alpine 11 PLUS	11 °C	45 dBA	2000 rpm	82 °C	71 °C
be quiet! Dark Rock 2	10 °C	41 dBA	1300 rpm	58 °C	48 °C
Phanteks PH-TC14CS	16 °C	47 dBA	1300 rpm	58 °C	42 °C
Phanteks PH-TC14PE	16 °C	48 dBA	1300 rpm	57 °C	41 °C
SilverStone HE01 (Q)	19 °C	44 dBA	1150 rpm	63 °C	44 °C
SilverStone HE01 (P)	20 °C	57 dBA	2050 rpm	62 °C	42 °C
Thermaltake WATER2.0 Extreme (S)	17 °C	44 dBA	1250 rpm	52 °C	35 °C
Thermaltake WATER2.0 Extreme (E)	17 °C	53 dBA	1900 rpm	50 °C	33 °C
Deepcool Neptwin	11 °C	46 dBA	1500 rpm	56 °C	45 °C
SilverStone HE02	19 °C	49 dBA	2000 rpm	64 °C	45 °C
Zalman CNPS9900DF	23 °C	45 dBA	1400 rpm	68 °C	45 °C
Deepcool ICE BLADE PRO V2.0	22 °C	43 dBA	1500 rpm	67 °C	45 °C
Phanteks PH-TC90LS	24 °C	47 dBA	2600 rpm	95 °C	71 °C
Rosewill AIOLOS	20 °C	40 dBA	1600 rpm	94 °C	74 °C
Corsair H60	20 °C	49 dBA	2000 rpm	64 °C	44 °C
Zalman LQ310	27 °C	51 dBA	2050 rpm	65 &d eg;C	38 °C
Noctua NH-L9i	24 °C	44 dBA	2500 rpm	95 °C	71 °C
NZXT Respire T40	20 °C	45 dBA	1850 rpm	76 °C	56 °C
NZXT Respire T20	21 °C	45 dBA	1900 rpm	77 °C	56 °C

In the graph below, you can see how many degrees Celsius hotter the CPU core is than the air outside the case. The lower this difference, the better is the performance of the cooler.

In the graph below, you can see how many decibels of noise each cooler makes.

[nextpage title=”Main Specifications”]

The main specifications for the NZXT Respire T20 CPU cooler include:

• Application: Sockets AM2(+), AM3(+), FM1, LGA775, LGA1155, LGA1156, LGA1366, and LGA2011
• Dimensions: 4.9 x 2.6 x 6.3 inches (124 x 65 x 160 mm) (W x L x H)
• Fins: Aluminum
• Base: Direct-touch heatpipes
• Heat-pipes: One 8-mm and two 6-mm copper heatpipes
• Fan: 120 mm
• Nominal fan speed: 1,800 rpm
• Fan air flow: 68.8 cfm
• Power consumption: 2.4 W
• Nominal noise level: 34 dBA
• Weight: 1.12 lb (510 g)
• More information: https://www.nzxt.com/
• Average Price in the U.S.*: USD 30.00

* Researched at Amazon.com on the day we published this review.

[nextpage title=”Conclusions”]

The unusual combination of one 8 mm center heatpipe and two 6 mm side ones, with no gap between them and directly touching the CPU, seems to work well. The NZXT Respire T20 reached the same performance level as its “bigger brother,” the Respire T40.

The NZXT Respire T20 is an excellent cooler, considering that it is inexpensive, quiet, and relatively small. It receives our Silver Award.