• Skip to primary navigation
  • Skip to main content
  • Skip to primary sidebar
  • Skip to footer
Hardware Secrets

Hardware Secrets

Uncomplicating the complicated

  • Case
  • Cooling
  • Memory
  • Mobile
    • Laptops
    • Smartphones
    • Tablets
  • Motherboard
  • Networking
  • Other
    • Audio
    • Cameras
    • Consumer Electronics
    • Desktops
    • Museum
    • Software
    • Tradeshows & Events
  • Peripherals
    • Headset
    • Keyboard
    • Mouse
    • Printers
  • Power
  • Storage
Home » Cougar Evolution Case Review

Cougar Evolution Case Review

[nextpage title=”Introduction”]

As you may know by now, Cougar is a brand that belongs to HEC/Compucase, and the Evolution is a mid-tower case with interesting features, such as a 3.5”/2.5” hot-swap docking station, a two-channel analog fan controller, and eight expansion slots, offered for USD 110 in the US. Let’s check it out.

Cougar Evolution caseFigure 1: Cougar Evolution case

Cougar Evolution caseFigure 2: Cougar Evolution case

The left panel of the Evolution has an L-shaped transparent window, plus a ventilation mesh that comes with an air filter installed, supporting a 140 mm fan that doesn’t come with the product.

Cougar Evolution caseFigure 3: Left-side panel

[nextpage title=”The Front Panel”]

The front panel of the Cougar Evolution has six external 5.25” bays, all using meshed covers, but no air filters.

Cougar Evolution caseFigure 4: Front panel

At the bottom part of the front panel, the Evolution comes with a 120 mm sleeve bearing fan (Power Logic PLA12025S12L-4, 1,500 rpm, 52.18 cfm, 28.2 dBA, which is commonly used in products from Xigmatek).

Cougar Evolution caseFigure 5: Front fan

[nextpage title=”The Top Panel”]

The top panel of the Evolution can be seen in Figure 6. It has a mesh, supporting the installation of two 120 mm fans. Two of the highlights of the reviewed case are found on its top panel, its two-channel fan controller and its hot-swap docking bay.

Cougar Evolution caseFigure 6: Top panel

The analog two-channel fan controller allows you to independently set the speed of two groups of fans. Each channel supports up to 1 A, which translates to 12 W at 12 V. The case comes with one adapter allowing you to connect up to three fans to a single channel, so you can control up to four fans (although three of them will run at the same speed). This controller uses three-pin fan power connectors.

The case also comes with two USB 3.0 ports, which are attached to a motherboard connector instead of regular USB plugs, so you won’t need to route the USB 3.0 cables to the outside of the case and install them on the USB 3.0 ports located at the motherboard rear panel. When buying this case, make sure to buy a motherboard that has at least one front panel header with two USB 3.0 ports available.

The Evolution also has two USB 2.0 ports and the traditional audio jacks.

Cougar Evolution caseFigure 7: Buttons and connectors

The hot-swap docking bay is hidden by a lid with the manufacturer’s logo. By pushing this lid down, you can install a 3.5” or 2.5” storage device.

Cougar Evolution caseFigure 8: Hot-swap docking bay

[nextpage title=”The Bottom and Rear Panels”]

The bottom panel has a big, removable air filter, covering the meshes available for the power supply fan and for an optional fan. This air filter is removed from the rear panel, so you don’t need to lift your case whenever you want to clean this filter.

Cougar Evolution caseFigure 9: Bottom panel

Cougar Evolution caseFigure 10: Air filter

The rear panel and the interior of the Evolution are painted black.

Another highlight of the Cougar Evolution is the presence of eight expansion slots. (Usually, cases have seven.) This allows you to install three or four video cards in your system, depending on your motherboard. The slot covers are vented.

There are two holes for hoses of liquid cooling solutions, but you have to break them if you want to use them. At least the case comes with two plastic rings to be installed in these holes.

The Evolution comes with a 120 mm fan identical to the one available on the front panel installed on its rear panel.

Cougar Evolution caseFigure 11: Rear panel

The reviewed case comes with a loop for you to install a padlock or warranty seal, preventing unauthorized people from opening the computer.

Cougar Evolution caseFigure 12: Loop for lock or warranty seal

Let’s now take a look inside the Cougar Evolution.[nextpage title=”Inside the Cougar Evolution”]

Both panels are attached to the chassis using black thumbscrews. The motherboard tray has a huge hole for you to access the backplate of the CPU cooler without having to remove the motherboard from the case, several holes for you to route cables behind it, and a few metallic clips for you to fasten cables using cable ties.

Cougar Evolution caseFigure 13: Overall look

Cougar Evolution caseFigure 14: A view behind the motherboard tray

In Figure 15, you have another overall look inside the case. The Evolution supports video cards up to 12” (305 mm) long and CPU coolers up to 7.1” (180 mm) tall.

Cougar Evolution caseFigure 15: Overall look

The power supply is installed at the bottom of the case. Note that it can be installed with either its bottom fan facing up or facing down, so you can decide if you want the fan of your power supply pulling air from inside the case or from outside of it.

The case comes with an adjustable bracket that you need to move to fit the power supply depth.

If you install a power supply up to 6.3” (160 mm) deep, you can install a 120 mm or 140 mm fan on the bottom panel. With a power supply up to 6.7” (170 mm) deep, you still can install a 120 mm fan. But if you have a power supply deeper than that, you won’t be able to install a fan on the bottom panel.

As shown before, the bottom panel has an air filter for the power supply fan and for this optional fan.

Cougar Evolution caseFigure 16: Power supply compartment

[nextpage title=”The Disk Drive Bays”]

The Cougar Evolution has six 5.25” external bays and a hard drive cage that has four 3.5”/2.5” bays. All bays use tool-less installation mechanisms, except when you have 2.5” devices.

Cougar Evolution caseFigure 17: Disk drive bays

You can remove the hard drive cage from the case. See Figure 18.

Cougar Evolution caseFigure 18: Hard drive cage

Each 3.5”/2.5” bay is actually a small drawer, with rubber rings around its pegs to absorb vibrations and, thus, reduce noise.

Cougar Evolution caseFigure 19: Drawer

[nextpage title=”Main Specifications”]

The main specifications for the Cougar Evolution case include:

  • Style: Mid-tower
  • Application: ATX and smaller form factors derived from this one
  • Material: Zinc-coated steel (SECC) body
  • Power supply: Doesn’t come with the product
  • Available colors: Black
  • Side panel: Meshed/transparent window
  • Dimensions: 20.2 x 8.8 x 20.6 inches (514 x 223 x 523 mm) (H x W x D)
  • Net weight: 19 lbs (8.6 kg)
  • Gross weight: 22.5 lbs (11 kg)
  • Bays: Six external 5.25” bays, one 3.5”/2.5” external bay with hot-swap connectors, and four internal 3.5”/2.5” bays
  • Expansion slots: Eight
  • Maximum video card length: 12” (305 mm)
  • Maximum CPU cooler height: 7.1” (180 mm)
  • Fans: One 120 mm fan on the front panel (1,500 rpm, 52.18 cfm, 28.2 dBA) and one 120 mm fan on the rear panel (1,500 rpm, 52.18 cfm, 28.2 dBA)
  • Optional fans: Two 120 mm fans on the top panel, one 140 mm fan on the left-side panel, and one 120 mm or 140 mm fan on the bottom panel
  • Extra features: Two-channel analog fan controller
  • More Information: https://www.cougar-world.com
  • Average Price in the US*: USD 110.00

* Researched at Newegg.com on the day we published this review.[nextpage title=”Conclusions”]

The Cougar Evolution is an excellent option for the user looking for a fully-loaded mid-tower case, coming at the right price. Therefore, it deserves our Golden Award.

Strong Points

  • Fair priced
  • Meshed bay covers
  • Vented slot covers
  • Air filter for the power supply fan
  • Air filter for the optional bottom fan
  • Air filter for the optional left-panel fan
  • Eight expansion slots
  • Two-channel analog fan controller
  • Hot-swap docking station
  • A huge hole in the motherboard tray for accessing the backplate of the CPU cooler
  • Holes for routing cables behind the motherboard tray

Weak Points

  • Covers of the holes for liquid cooling solutions need to be manually broken
  • No air filters on the bay covers
  • No air filter for the front fan

Reader Interactions

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Primary Sidebar

As a participant in the Amazon Services LLC Associates Program, this site may earn from qualifying purchases. We may also earn commissions on purchases from other retail websites.

car service

Why Is Fleet Maintenance Important?

If you have a fleet of vehicles you use within your business, it’s crucial you keep up with their

Playing Fifa on Play station 4

Tips for Recycling Your Gaming Consoles and Devices

These days, it seems like almost everybody is gaming. As great as this is, it’s also creating a

Business planning

How to Develop Your Venture Capital Business

Venture Capital (VC) is a type of private equity investment in which investors provide funding to

Footer

For Performance

  • PCI Express 3.0 vs. 2.0: Is There a Gaming Performance Gain?
  • Does dual-channel memory make difference on integrated video performance?
  • Overclocking Pros and Cons
  • All Core i7 Models
  • Understanding RAM Timings

Everything you need to know

  • Everything You Need to Know About the Dual-, Triple-, and Quad-Channel Memory Architectures
  • What You Should Know About the SPDIF Connection (2022 Guide)
  • Everything You Need to Know About the Intel Virtualization Technology
  • Everything You Need to Know About the CPU Power Management

Copyright © 2023 · All rights reserved - Hardwaresecrets.com
About Us · Privacy Policy · Contact