We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.

[nextpage title=”Introduction”]

The Xigmatek Loki is a CPU cooler with tower heatsink, three U-shaped heatpipes and a 92 mm fan. Let’s check it out!

It is curious that Xigmatek offers a CPU cooler named Thor’s Hammer (which we already tested) and another one named Loki, since in Norse mythology (and in Marvel Comics stories as well) Loki is Thor’s adversary. We cannot understand the point in naming a product after a bad guy.

The Loki box is small and simple, as you can see in Figure 1.

Figure 1: Package

The box contents are shown in Figure 2: heatsink, fan, manuals, thermal compound, and installation hardware. The cooler came with only one fan, but it comes with the hardware necessary to install a second 92 mm fan.

Figure 2: Accessories

Figure 3 shows the Xigmatek Loki heatsink.

Figure 3: The Xigmatek Loki heatsink

This cooler is discussed in detail in the following pages.

[nextpage title=”The Xigmatek Loki”]

Figure 3 shows the cooler from the front. Here you can see the border fins are irregular.

Figure 4: Front view

In Figure 5, you see the side of the heatsink. The folded fins make an almost completely closed surface.

Figure 5: Side view

On the top of the heatsink, shown in Figure 6, you can see the slots for installing the fans on both sides. The tips of the three U-shaped heatpipes are also visible.

Figure 6: Top view

[nextpage title=”The Xigmatek Loki (Cont’d)”]

The base of the cooler is shown in Figure 7. The heatpipes touch the CPU directly, and there is a big gap between them.

Figure 7: Base

In Figure 8, you can see the 92 mm fan that comes with the Xigmatek Loki. It is a PWM model, thus having four pins in the connector.

Figure 8: Fan

Figure 9 reveals the Xigmatek Loki with the fan in place. It is held by four rubber pieces.

Figure 9: Fan installed

[nextpage title=”Installation”]

Figure 10 shows the clips for installation on Intel CPUs screwed to the base of the cooler.

Figure 10: Clips installed

Figure 11 presents the universal backplate with the screws inserted in holes corresponding to socket LGA1156 (at the left) and the clip for use with AMD processors (at the right).

Figure 11: Backplate and AMD clip

The backplate must be inserted from the solder side of the motherboard, and then held in place by four thumbnuts, as shown in Figure 12.

Figure 12: Backplate installed

After that, you need to put the cooler over the CPU, and then screw four nuts. Figure 13 shows the Xigmatek Loki installed, with the fan already in place.

Figure 13: Cooler installed

We installed the cooler according to the manual, as shown in the pictures on this page, but when we turned on the computer, the cooling performance was so poor that the computer shut down as soon as we demanded the CPU. We revised the installation and noticed that the cooler was barely touching the CPU, but not pressing it, due to the height of the thumbnuts, which kept us from applying pressure on the clip. So we reinstalled the clips in the position shown in Figure 14, which solved the problem.

Figure 14: New position for the clips

[nextpage title=”How We Tested”]

We tested the cooler with a Core i7-860 CPU (quad-core, 2.8 GHz), which is a socket LGA1156 processor with a 95 W TDP (Thermal Design Power). In order to get higher thermal dissipation, we overclocked it to 3.3 GHz (150 MHz base clock and 22x multiplier), keeping the standard core voltage (Vcore), which was the maximum stable overclock we could make with the stock cooler. Keep in mind that we could have raised the CPU clock more, but to include the stock cooler in our comparison, we needed to use this moderate overclock.

We measured noise and temperature with the CPU idle and under full load. In order to get 100% CPU usage in all threads, we ran Prime 95 25.11 with the "In-place Large FFTs" option. (In this version, the software uses all available threads.)

We compared the tested cooler to the Intel stock cooler with a copper base (included with the CPU), as well as with other coolers. Note that in the past, we tested coolers with a socket LGA775
CPU, and we retested some "old" coolers with this new methodology. This means you can find different values in older reviews than the values you will read in the next page. Every cooler was tested with the thermal compound that accompanies it.

Room temperature measurements were taken with a digital thermometer. The core temperature was read with the SpeedFan program (available from the CPU thermal sensors), using an arithmetic average of the core temperature readings. During the tests, the left panel of the case was open.

The sound pressure level (SPL) was measured with a digital noise meter, with its sensor placed 4" (10 cm) from the fan. We turned off the case and video board cooler fans so they wouldn’t interfere with the results. This measurement is only for comparison purposes, because a precise SPL measurement needs to be made inside an acoustically insulated room with no other noise sources, which isn’t the case here.

Hardware Configuration

• Processor: Core i7-860
• Motherboard: Gigabyte P55A-UD6
• Memory: 2 GB Markvision (DDR3-1333/PC3-10700 with 9-9-9-22 timings), configured at 1,200 MHz
• Hard disk: Seagate Barracuda XT 2 TB
• Video card: Zotac GeForce GTS 250
• Video resolution: 1680×1050
• Video monitor: Samsung Syncmaster 2232BW Plus
• Power supply: Seventeam ST-550P-AM
• Case: 3RSystem L-1100 T.REX Cool

Operating System Configuration

• Windows 7 Home Premium 64 bit SP1

Software Used

• Prime95
• SpeedFan

Error Margin

We adopted a 2 °C error margin, meaning temperature differences below 2 °C are considered irrelevant.

[nextpage title=”Our Tests”]

The table below presents the results of our measurements. We repeated the same test on all coolers listed below. Each measurement was taken with the CPU at idle and at full load. In the models with a fan supporting PWM, the motherboard controlled the fan speed according to core load and temperature. On coolers with an integrated fan controller, the fan was set at the minimum speed on the idle test and at full speed on the full load test.

		Idle Processor			Processor at Full Load
Cooler	Room Temp.	Noise	Speed	Core Temp.	Noise	Speed	Core Temp.
Intel stock (socket LGA1156)	14 °C	44 dBA	1700 rpm	46 °C	54 dBA	2500 rpm	90 °C
Cooler Master Hyper TX3 G1	14 °C	47 dBA	2050 rpm	33 °C	56 dBA	2900 rpm	62 °C
Zalman CNPS10X Extreme	14 °C	45 dBA	1400 rpm	27 °C	53 dBA	1950 rpm	51 °C
Thermaltake Silent 1156	14 °C	44 dBA	1200 rpm	38 °C	49 dBA	1750 rpm	69 °C
Noctua NH-D14	14 °C	49 dBA	1250 rpm	27 °C	49 dBA	1250 rpm	53 °C
Zalman CNPS10X Performa	14 °C	46 dBA	1500 rpm	28 °C	52 dBA	1950 rpm	54 °C
Prolimatech Megahalems	14 °C	40 dBA	750 rpm	27 °C	60 dBA	2550 rpm	50 °C
Thermaltake Frio	14 °C	46 dBA	1450 rpm	27 °C	60 dBA	2500 rpm	50 °C
Prolimatech Samuel 17	14 °C	40 dBA	750 rpm	40 °C	60 dBA	2550 rpm	63 °C
Zalman CNPS8000A	18 °C	43 dBA	1400 rpm	39 °C	54 dBA	2500 rpm	70 °C
Spire TherMax Eclipse II	14 °C	55 dBA	2200 rpm	28 °C	55 dBA	2200 rpm	53 °C
Scythe Nin ja3	17 °C	39 dBA	700 rpm	32 °C	55 dBA	1800 rpm	57 °C
Corsair A50	18 °C	52 dBA	1900 rpm	33 °C	52 dBA	1900 rpm	60 °C
Thermaltake Jing	18 °C	44 dBA	850 rpm	34 °C	49 dBA	1300 rpm	60 °C
GlacialTech Alaska	18 °C	43 dBA	1150 rpm	36 °C	51 dBA	1600 rpm	60 °C
Deepcool Gamer Storm	18 °C	43 dBA	1100 rpm	35 °C	48 dBA	1600 rpm	62 °C
Corsair A70	26 °C	56 dBA	1900 rpm	40 °C	56 dBA	1900 rpm	65 °C
Deepcool Ice Blade Pro	23 °C	45 dBA	1200 rpm	38 °C	52 dBA	1500 rpm	64 °C
AC Freezer 7 Pro Rev. 2	23 °C	47 dBA	1750 rpm	44 °C	51 dBA	2100 rpm	77 °C
Corsair H70	27 °C	60 dBA	1900 rpm	37 °C	60 dBA	1900 rpm	61 °C
Zalman CNPS9900 Max	27 °C	55 dBA	1600 rpm	38 °C	58 dBA	1750 rpm	63 °C
Arctic Cooling Freezer 11 LP	25 °C	45 dBA	1700 rpm	51 °C	49 dBA	1950 rpm	91 °C
CoolIT Vantage	26 °C	60 dBA	2500 rpm	37 °C	60 dBA	2500 rpm	62 °C
Deepcool Ice Matrix 600	25 °C	46 dBA	1100 rpm	41 °C	53 dBA	1300 rpm	69 °C
Titan Hati	26 °C	46 dBA	1500 rpm	40 °C	57 dBA	2450 rpm	68 °C
Arctic Cooling Freezer 13	27 °C	49 dBA	1950 rpm	41 °C	53 dBA	2300 rpm	70 °C
Noctua NH-C14	26 °C	52 dBA	1300 rpm	37 °C	52 dBA	1300 rpm	61 °C
Intel XTS100H	26 °C	49 dBA	1200 rpm	42 °C	64 dBA	2600 rpm	68 °C
Zalman CNPS5X SZ	23 °C	52 dBA	2250 rpm	38 °C	57 dBA	2950 rpm	69 °C
Thermaltake SlimX3	21 °C	50 dBA	2700 rpm	46 °C	50 dBA	2750 rpm	99 °C
Cooler Master Hyper 101	21 °C	50 dBA	2600 rpm	38 °C	57 dBA	3300 rpm	71 °C
Antec Kühler H2O 620	19 °C	52 dBA	1400 rpm	34 °C	55 dBA	1400 rpm	58 °C
Arctic Cooling Freezer 13 Pro	20 °C	46 dBA	1100 rpm	36 °C	49 dBA	1300 rpm	62 °C
GlacialTech Siberia	22 °C	49 dBA	1400 rpm	34 °C	49 dBA	1400 rpm	61 °C
Evercool Transformer 3	18 °C	46 dBA	1800 rpm	33 °C	51 dBA	2250 rpm	65 °C
Zalman CNPS11X Extreme	20 °C	51 dBA	1850 rpm	34 °C	56 dBA	2050 rpm	61 °C
Thermaltake Frio OCK	15 °C	44 dBA	1000 rpm	27 °C	64 dBA	2200 rpm	51 °C
Prolimatech Genesis	18 °C	49 dBA	1050 rpm	30 °C	49 dBA	1050 rpm	54 °C
Arctic Cooling Freezer XTREME Rev. 2	15 °C	41 dBA	1050 rpm	32 °C	44 dBA	1400 rpm	60 °C
NZXT HAVIK 140	16 °C	48 dBA	1250 rpm	29 °C	49 dBA	1250 rpm	55 °C
Antec Kühler H2O 920	18 °C	41 dBA	650 rpm	29 °C	64 dBA	2500 rpm	49 °C
Zalman CNP7X LED	18 °C	45 dBA	1950 rpm	33 °C	48 dBA	2150 rpm	58 °C
EVGA Superclock	14 °C	43 dBA	1300 rpm	27 °C	58 dBA	2350 rpm	47 °C
Evercool Transformer 4	15 °C	46 dBA	1500 rpm	26 °C	53 dBA	1950 rpm	52 °C
Xigmatek Dark Knight	18 °C	47 dBA	1700 rpm	30 °C	53 dBA	2150 rpm	57 °C
Xigmatek Aegir	15 °C	44 dBA	1500 rpm	27 °C	50 dBA	1950 rpm	52 °C
Cooler Master GeminII S524	16 °C	45 dBA	1300 rpm	29 °C	53 dBA	1800 rpm	58 °C
Enermax ETS-T40-TA	16 °C	40 dBA	1050 rpm	28 °C	48 dBA	1800 rpm	55 °C
Corsair H80	14 °C	42 dBA	2150 rpm	25 °C	52 dBA	2150 rpm	47 °C
Akasa Venom Voodoo	13 °C	40 dBA	1000 rpm	26 °C	48 dBA	1500 rpm	51 °C
Xigmatek Thor’s Hammer	15 °C	44 dBA	1500 rpm	30 °C	50 dBA	2000 rpm	55 °C
Cooler Master Hyper 612 PWM	19 °C	45 dBA	1 400 rpm	30 °C	52 dBA	1900 rpm	54 °C
Xigmatek Loki	17 °C	44 dBA	1850 rpm	34 °C	55 dBA	2750 rpm	60 °C

In the graph below, at full load you can see how many degrees Celsius hotter the CPU core is than the air outside the case. The lower this difference, the better is the performance of the cooler.

 

[nextpage title=”Main Specifications”]

The main specifications for the Xigmatek Loki CPU cooler include:

• Application: Sockets 775, 1155, 1156, 1366, AM2, AM2+, AM3, AM3+, and FM1 processors
• Dimensions: 3.6 x 1.9 x 5.3 inches (92 x 50 x 134 mm) (W x L x H)
• Fins: Aluminum
• Base: Aluminum, with heatpipes in direct contact to the CPU
• Heat-pipes: Three copper heatpipes
• Fan: One 92 mm fan (supports two fans)
• Nominal fan speed: 2,800 rpm
• Fan air flow: 52 cfm
• Maximum power consumption: 4 W
• Nominal noise level: 28 dBA
• Weight: 11.6 oz (330 g)
• More information: https://www.xigmatek.com
• Average price in the US*: USD 29.00

* Researched at Newegg.com on the day we published this review.[nextpage title=”Conclusions”]

Although the Loki character in fiction and mythology is a villain, the Xigmatek Loki is a good value/mainstream CPU cooler. It performed better than the Cooler Master Hyper TX3, from whom it seems to be “inspired.”

It is a shame that the Xigmatek Loki has an installation issue that prevents it from correctly pressing the CPU. This must be corrected by the manufacturer, but you can easily avoid problems by installing the clips over the base and not under it, or even bending the holding arms in order to allow the screws to apply force.

Considering its good cooling performance and excellent price/performance ratio, the Xigmatek Loki receives our Bronze Award.